Maiden Flight | RS1

Lift Off Time
(Subject to change)
NET October 10, 2022 – 22:00 UTC | 14:00 AKDT
Mission Name
RS1 Maiden Flight
Launch Provider
(What rocket company is launching it?)
ABL Space Systems
Customer
(Who’s paying for this?)
Omniteq
Rocket
RS1
Launch Location
Pad 3C, Pacific Spaceport Center, Kodiak Island, Alaska, USA
Payload mass
∼22 kg
Where are the satellites going?
350 x 200 km elliptical orbit with an inclination of 87.3°
Will they be attempting to recover the first stage?
No, RS1 is not capable of recovery
Where will the first stage land?
It will crash in the Pacific ocean
Will they be attempting to recover the fairings?
No, RS1 is not capable of recovery
Are these fairings new?
Yes
How’s the weather looking?
TBD
This will be the:
1st RS1 orbital launch attempt
– 123rd orbital launch attempt of 2022
Where to watch
Once available, an official livestream will be listed here

What Does All This Mean?

ABL Space Systems is preparing for the maiden flight of its RS1 rocket. The launch vehicle will lift off from the Pacific Spaceport Center in Alaska and will carry two satellites for Omniteq (Varisat-1A and Varisat-1B).

ABL Space Systems

ABL Space Systems (ABL) was founded in 2017. The company still keeps in secret what the ABL and RS1 acronyms stand for. Based in El Segundo, California, ABL already occupies several facilities with end-to-end manufacturing capabilities in-house. The company has two test sites, the first one is located at the Mojave Air and Spaceport and has two active engine test bays, and the second one is located at Edwards Air Force Base and is used for general testing.

Harry O’Hanley is the Chief executive officer (CEO) and Dan Piemont is the Chief financial officer (CFO) of ABL Space Systems.

Maiden Flight

Payload

On its maiden launch, the RS1 rocket will carry two satellites (Varisat-1A and Varisat-1B) for Omniteq to their designated orbit with a 350 km apogee, a 200 km perigee, and an inclination of 87.3 degrees. Varisat-1A&B are technology demonstration satellites that are composed of two identical 6U CubeSats. The total mass of each satellite is about 11 kg.

The spacecraft will be demonstrating a new HF marine data communications capability. The satellites are gravity gradient and aerodynamic drag stabilized and have six deployable solar array panels. There is no propulsion on the satellites.

One of Omniteq’s satellites, Varisat-1C, has been already delivered to its designated orbit on the Transporter-5 mission, on May 25, 2022. Additional information about Varisat-1 satellites can be found here.

Testing Before The Maiden Flight

In 2019, the company carried out testing of the E2 engine at Spaceport America, the campaign was a success. The team was able to rapidly activate its deployable test site and was happy with how the engine performed.

Then, in October 2020, ABL performed a series of static-fire tests of the upper stage at Edwards Air Force Base. These tests consisted of the stage fueling, refining startup sequences, and firing its vacuum-optimized E2 engine. By that time, the company aimed to conduct the maiden flight in 2021.

RS1 upper during testing, preparations for maiden flight
The upper stage during its testing. (Credit: ABL Space Systems)

In January 2022, ABL lost an upper stage during a static firing at the Mojave Air and Spaceport, which was caused by a hard start of the E2 vacuum engine and delayed the vehicle’s first flight. After this accident, the company was able to build the stage in only three weeks and proceeded with its testing.

In May 2022, the company completed acceptance testing of the upper stage. After that, it was shipped to its launch site in Kodiak, Alaska. Check out the video on ABL’s YouTube channel showing a static-fire test of the stage and its loading to the standard 20′ container!

Finally, on July 9, the company successfully performed a static-fire test of the first stage at Pacific Spaceport Center, Alaska.

What Is RS1?

ABL’s RS1 is a ground-launched small-lift rocket consisting of two stages. When fully integrated, RS1 has a length of about 26.8 m (88 ft) and a diameter of 1.8 m (6 ft). The rocket’s design is deliberately simple, which allows the company to rapidly produce reliable, low-cost, and simple in operation launch vehicles. The company’s philosophy is perfectly described by the slogan on its website “Even rockets can be simple”.

The RS1 rocket, launch pad, preparing for maiden flight
The RS1 rocket on the launch pad. (Credit: ABL Space Systems)

One interesting thing about RS1 is that all its stages are sized to fit in standard shipping containers that could be delivered to the desired launch site. For instance, the first stage can be shipped in a 53′ container, whereas the second stage and fairing – in 20′ containers. Moreover, the only piece of ground infrastructure required at the launch site is a flat concrete pad with dimensions of 150′ x 50′. With this approach, the company will be able to provide responsive launch services by activating launch sites quickly, at a low cost, and with a small team.

The vehicle’s structures are entirely metallic and made of high-strength aluminum alloy. The propellant tank architecture represents a common dome and yields minimized structural mass. The vehicle’s dry weight is about 3,200 kg (7,000 lb), while its gross lift-off weight is about 6,800 kg (15,000 Ib). RS1 is capable of placing 1,350 kg to low Earth orbit (LEO) and 970 kg to a 500 km Sun-Synchronous orbit (SSO).

First And Second Stages

First StageSecond Stage
Engine9 E2 engines1 vacuum optimized E2 engine
Thrust485 kN (109,000 Ibf)58 kN (13,000 Ibf)

First Stage

The first stage has a length of 15 m (50 ft) and uses nine E2 Sea Level engines that work on liquid oxygen (LOx) as the oxidizer and kerosene as the propellant.

RS1 first stage
The first stage during its static-fire test. (Credit: ABL Space Systems)

E2 Engine

E2 engines are the main propulsion source for RS1 that was designed and developed in-house, specifically for this vehicle. They are gas generator cycle, turbopump-fed engines running on kerosene (RP-1 or Jet-A) and liquid oxygen (LOx). The E2 engine is capable of producing 12,100 Ibf at sea level and 13,000 in a vacuum.

The E2 engine, RS1, ABL space systems
The E2 engine. (Credit: ABL Space Systems)

The company combines a traditional approach (forging and machining method) and additive manufacturing for building different components of the rocket. For example, 3D printing with the following post-processing is used for components that require complex internal geometry and fluid passageways (e.g., a thrust chamber, an injector, and turbopumps). The E2 thrust chamber is made of high-performance nickel alloy using a direct metal laser sintering (DMLS) method. In this process, the metal powder is melted by the scanning of a high-power laser beam. It has high detail resolution due to the small powder diameter (20 um) and is widely used for the fabrication of aerospace parts for high heat applications. At the same time, the company uses well-established forging and machining methods for components that are less complex.

Second Stage

The second stage has a length of 1.6 m (5.4 ft) and accommodates one E2 vacuum engine that also runs on kerosene and LOx. It can relight to deliver payloads to their designated orbits.

Fairing

The front end of the vehicle includes a custom-designed payload adapter fitting and a metallic bi-conic fairing with acoustic protection. RS1 can use two types of fairings: standard and expanded. The standard type has a diameter of 2.0 m (80”), while the expanded type has a diameter of 2.7 m (108”). The fairing consists of two parts and separates along a longitudinal seam using low shock pneumatic actuators.

Mission Profile

The stage separation occurs at approximately 160 s into the flight, at an altitude of 75 km. The fairing separates at 200 s, at an altitude of 125 km. In a typical mission, SECO-1 takes place at approximately 508 s, at an altitude of 208 km. All the separation devices are non-pyrotechnic.

Reference Mission Timeline

Hrs:Min:Sec
From Lift-Off
Events
– 00:00:02Stage 1 Startup
00:00:00Lift-Off
+ 00:01:18Maximum Dynamic Pressure (MaxQ)
+ 00:02:58Main Engine Cut Off (MECO)
+ 00:03:00Stage 1 Separation
+ 00:03:04Stage 2 Startup 1
+ 00:03:16Fairing Separation
+ 00:07:59Second Engine Cut Off (SECO)
+ 00:08:37Payload Deploy
+ 00:10:00Collision Avoidance Maneuver (CAM)
+ 00:15:00Deorbit Burn

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.

%d bloggers like this: